SOCKET Section: Linux Programmer's Manual (2) Updated: 24 Apr 2025 Index   NAME socket - create an endpoint for communication   SYNOPSIS #include <sys/types.h> #include <sys/socket.h> int socket(int domain, int type, int protocol);   DESCRIPTION Socket creates an endpoint for communication and returns a descriptor. The domain parameter specifies a communication domain; this selects the protocol family which will be used for communication. These families are defined in <sys/socket.h>. The currently understood formats include: PF_UNIX, PF_LOCAL UNIX protocols for local communication PF_INET IPv4 Internet protocols; see PF_INET6 IPv6 Internet protocols PF_IPX IPX - Novell protocols PF_NETLINK Kernel user interface device PF_X25 ITU-T X.25 / ISO-8208 protocol PF_AX25 Amateur radio AX.25 protocol PF_ATMPVC Access to raw ATM PVCs PF_APPLETALK Appletalk; see PF_PACKET Low level packet interface; see The socket has the indicated type, which specifies the communication semantics. Currently defined types are: SOCK_STREAM Provides sequenced, reliable, two-way, connection-based byte streams. An out-of-band data transmission mechanism may be supported. SOCK_DGRAM Supports datagrams (connectionless, unreliable messages of a fixed maximum length). SOCK_SEQPACKET Provides a sequenced, reliable, two-way connection-based data transmission path for datagrams of fixed maximum length; a consumer is required to read an entire packet with each read system call. SOCK_RAW Provides raw network protocol access. SOCK_RDM Provides a reliable datagram layer that does not guarantee ordering. SOCK_PACKET Obsolete and should not be used in new programs; see Some socket types may not be implemented by all protocol families; for example, SOCK_SEQPACKET is currently not implemented in Linux for AF_INET. The protocol specifies a particular protocol to be used with the socket. Normally only a single protocol exists to support a particular socket type within a given protocol family. However, it is possible that many protocols may exist, in which case a particular protocol must be specified in this manner. The protocol number to use is specific to the ``communication domain'' in which communication is to take place; see See on how to map protocol name strings to protocol numbers. Sockets of type SOCK_STREAM are full-duplex byte streams, similar to pipes. A stream socket must be in a connected state before any data may be sent or received on it. A connection to another socket is created with a call. Once connected, data may be transferred using and calls or some variant of the and calls. When a session has been completed a may be performed. Out-of-band data may also be transmitted as described in and received as described in The communications protocols which implement a SOCK_STREAM ensure that data is not lost or duplicated. If a piece of data for which the peer protocol has buffer space cannot be successfully transmitted within a reasonable length of time, then the connection is considered to be dead. When SO_KEEPALIVE is enabled on the socket the protocol checks in a protocol-specific manner if the other end is still alive. A SIGPIPE signal is raised if a process sends or receives on a broken stream; this causes naive processes, which do not handle the signal, to exit. SOCK_SEQPACKET sockets employ the same system calls as SOCK_STREAM sockets. The only difference is that calls will return only the amount of data requested, and any remaining in the arriving packet will be discarded. Also all message boundaries in incoming datagrams are preserved. SOCK_DGRAM and SOCK_RAW sockets allow sending of datagrams to correspondents named in calls. Datagrams are generally received with which returns the next datagram with its return address. SOCK_PACKET is an obsolete socket type to receive raw packets directly from the device driver. Use instead. An call with the the F_SETOWN argument can be used to specify a process group to receive a SIGURG signal when the out-of-band data arrives or SIGPIPE signal when a SOCK_STREAM connection breaks unexpectedly. It may also be used to set the process or process group that receives the I/O and asynchronous notification of I/O events via SIGIO. Using F_SETOWN is equivalent to an call with the SIOSETOWN argument. When the network signals an error condition to the protocol module (e.g. using a ICMP message for IP) the pending error flag is set for the socket. The next operation on this socket will return the error code of the pending error. For some protocols it is possible to enable a per-socket error queue to retrieve detailed information about the error; see IP_RECVERR in The operation of sockets is controlled by socket level options. These options are defined in <sys/socket.h>. and are used to set and get options, respectively.   RETURN VALUES -1 is returned if an error occurs; otherwise the return value is a descriptor referencing the socket.   ERRORS EPROTONOSUPPORT The protocol type or the specified protocol is not supported within this domain. ENFILE Not enough kernel memory to allocate a new socket structure. EMFILE Process file table overflow. EACCES Permission to create a socket of the specified type and/or protocol is denied. ENOBUFS or ENOMEM Insufficient memory is available. The socket cannot be created until sufficient resources are freed. EINVAL Unknown protocol, or protocol family not available. Other errors may be generated by the underlying protocol modules.   CONFORMING TO 4.4BSD (the socket function call appeared in 4.2BSD). Generally portable to/from non-BSD systems supporting clones of the BSD socket layer (including System V variants).   NOTE The manifest constants used under BSD 4.* for protocol families are PF_UNIX, PF_INET, etc., while AF_UNIX etc. are used for address families. However, already the BSD man page promises: "The protocol family generally is the same as the address family", and subsequent standards use AF_* everywhere.   SEE ALSO lqAn Introductory 4.3 BSD Interprocess Communication Tutorialrq is reprinted in UNIX Programmer's Supplementary Documents Volume 1. lqBSD Interprocess Communication Tutorialrq is reprinted in UNIX Programmer's Supplementary Documents Volume 1.   Index NAME SYNOPSIS DESCRIPTION RETURN VALUES ERRORS CONFORMING TO NOTE SEE ALSO This document was created by using the manual pages. Time: 11:56:07 GMT, March 24, 2025