Next Previous Contents 3. General Setup and Kernel Module Issues 3.1 Kernel Module Support All of the drivers listed here are released as kernel modules; therefore, you must be sure to have a kernel which supports modules. In addition, "module version" support should be enabled to aid the use of kernels and modules which are not version matched, as described further below. If you use a kernel from a reasonably recent Linux distribution, module support is most likely already enabled. If you're compiling the kernel yourself, then you should already be aware of how to enable modules, via the Kernel HOWTO. In any case, you can check to make sure that the following settings exist in your kernel configuration file (which is usually found under /usr/src/linux): CONFIG_MODULES=y CONFIG_MODVERSIONS=y 3.2 Sound Support This is a newly recognized factor as of October, 2000, and should be considered anecdotal until information on further hardware/software combinations is gathered. Marv Stodolsky has observed that with the binary-only Lucent driver (v5.68), sound support must be enabled in the kernel (support via sound modules is OK), or else a dail-in session utilizing the ltmodem.o driver aborts/hangs when the ppp protocol is initiated. The combination of OSS software providing all audio support (with a kernel without sound compiled in) failed to support the ppp protocol through the ltmodem.o driver. How broadly valid these "sound" factors for other Linmodems/Audio_cards remains to be clarified. 3.3 ISA Plug-n-Play If you have an ISA Plug-n-Play modem, you will most likely need to use isapnptools to allocate resources to the modem card. For this, you need to have isapnptools installed and have an entry in the /etc/isapnp.conf file for the modem. You should read the manual pages and the Plug-and-Play-HOWTO, but if you have no other ISA devices you're concerned about, basically all you need to do is: If possible, configure your BIOS to "Non-PNP OS." As root, run pnpdump to generate a prototype isapnp.conf file based on probed cards and your system's current resource usage. Look for your modem in this output, and uncomment the lines corresponding to the (otherwise unused) IRQ you wish to use for the modem. For example, Sean's isapnp.conf for a Thinkpad i1411 with a Lucent LT modem includes: (CONFIGURE ACRd119/1 (LD 0 (INT 0 (IRQ 11 (MODE +E))) (IO 1 (SIZE 8) (BASE 0x0100) (CHECK)) (NAME "ACRd119/1[0]{LT Win Modem }") # (ACT Y) )) Strangely, in this case at least, it was necessary to leave the #(ACT Y) commented out. If it doesn't work for you one way, try it the other. Copy the file to /etc/isapnp.conf Reboot. You should see a message along the lines of 'Initializing ISA PNP devices...OK' on booting. If it fails, you have probably selected an IRQ/DMA setting which is already in use; try another of the options given in the pnpdump output. (Note that it is probably not necessary to reboot, if you run isapnp with the right flags. However, it's easiest for the beginner to simply reboot at this point.) 3.4 PCI Modems If you wish to know more about your PCI modem than cat /proc/pci gives, utilities within the software package pciutils are useful, such as scanpci and lspci. 3.5 Module tools The following commands are useful when dealing with modules. Many require root priveleges. See the manual pages (e.g., man insmod) for more detailed information on these commands. insmod -f A version-matched kernel module is inserted using the command insmod module_name. If the module were compiled under a different kernel than the current one, insmod would report the version mismatch and refuse load the module. One can, however, pass a flag to force the module to load despite the mismatch: insmod -f module_name. If the kernel interface the module uses did not actually change with the kernel version, the module will be inserted and could be to some degree functional. This is the case with, for example, the ESS modem module esscom.o which, while compiled under 2.2.12, can be forcibly inserted with later kernels and will function to a greater or lesser extent up through kernel version 2.2.14 without further changes; beyond 2.2.15, the patch to tty.h described below is required. However, even forcing insertion fails for kernels compiled from the rapidly maturning 2.4.0-testX sources. modprobe The command modprobe modulename will insert a module and all of the modules required by that module (as determined by depmod, described below). rmmod A module can be unloaded (removed from the kernel) after use by issuing the command rmmod. depmod The depmod commands analyses module dependencies. The compatility of precompiled modules with a running kernel can be checked with a command like: depmod -e ltmodem.o For the specific case of the ltmodem.o compiled under kernel 2.2.12 with a running kernel 2.2.17, the returned information includes: depmod: *** Unresolved symbols in ltmodem.o depmod: bh_mask depmod: schedule_timeout depmod: request_region depmod: pcibios_read_co and many others. Using a module with unresolved symbols can be a dangerous thing, as described below. Next Previous Contents